数控采暖锅炉的燃烧方式及供水系统
    2014-1-7 15:44:50  文章来源:http://www.jnlzsb.com
    采暖炉在使用期间要保证炉内的煤充分燃烧,并且提高燃烧的效率,减少原料和资源的浪费,保证强大的转换作用和价值。充分利用煤气燃烧,则大大提高的燃烧效率,达到同样的采暖效果。又加设了超强转化系统,使燃气稳定,利用了超导换热技术,升温速度快、能耗少、无污染,气火燃烧时烧烟煤不冒烟,符合环保要求,操作方便,添煤即可产气,随时可以使用,是新一代节煤采暖炉. 高效节能的采暖炉在使用中具有良好的使用和转换功率,能够保证室内和人们的需要,为人们提供更多的方便和舒适,增加中要的价值作用。高效节能,环保多功能制气采暖炉。数控采暖锅炉http://www.jnlzsb.com/
    Cainuanlu during use to ensure that the coal inside the furnace combustion fully, and increase the combustion efficiency, reduce the waste of raw materials and resources, ensure the powerful transformation function and value. Make full use of the gas combustion, greatly improve the combustion efficiency, achieve the same heating effect. And adding super conversion systems, stability, gas use of superconducting heat transfer technology, heating speed, less energy consumption, no pollution, not smoke gas fire burning bituminous coal, conforms to the requirements of environmental protection, easy to operate, add coal to gas, can be used at any time, is a new generation of coal saving cainuanlu. High efficiency and energy saving of cainuanlu in use with good use and transfer power, to assure indoor and people's needs, to provide more convenient and comfortable for people, to increase the value of the function. High efficiency and energy saving, environmental protection multifunctional gasification cainuanlu licensing.
    数控锅炉彻底改变了传统燃煤锅炉的燃烧方式,将燃煤中挥发成分充分转化后进行气化燃烧,致使燃料中的可燃烧成分得以全部利用,而且燃烧强度高,火焰温度可达1300~(3以上。多点回程螺纹烟管绕动技术,有效增加了换热面积,再结合整体保温措施,使锅炉的换热效率提高40%~50%,实现了仅为200qC左右低温排放,降低了热量流失。
    Numerical control boiler thoroughly changed the traditional coal-fired boiler combustion mode, after turn coal volatile component fully gasification combustion, cause the fuel to burn in the composition to be able to use all, and combustion intensity is high, the flame temperature can reach 1300 ~ (more than 3. More return threaded pipe winding technology, effectively increase the heat transfer area, combined with the overall heat preservation measures, make the boiler in thermal efficiency is increased by 40% ~ 50%, achieved was only about 200 qc emissions at low temperature, reduce the heat loss.
    数控锅炉使用前检查数控锅炉各个人孔、手孔、各阀门等杜绝漏气、漏水现象,检查供气、供水系统防止跑漏滴,确保安全,检查数控锅炉辅机设备,确保其正常运行,检查各仪表灵敏性,指示正常,检查紧固然燃烧机各连接部位,防患未然,检查可燃气体泄漏检测系统,温度控制系统,防雷系统;必须保证系统的灵敏性,可靠性,安全性。至于定期保养则主要是在数控锅炉运行中两周一次的日常巡检,消除运行隐患,需要注意的事项有,全面检查安全装置,检查燃烧机运行状况,检查控制系统联锁装置是否正常。数控采暖锅炉http://www.jnlzsb.com/
    Numerical control boiler inspection before use numerical control boiler each manhole, hand hole and the valve to eliminate leakage, leakage phenomenon, check the gas supply, water supply system to prevent run LouDi, ensure the safety, check of nc boiler auxiliary equipment, to ensure the normal operation, check the instrument sensitivity, indicating normal, check the connection part is burning machine, be safe, check for combustible gas leak detection system, temperature control system, lightning protection system; Must ensure that the system's sensitivity, reliability and security. As for regular service are mainly in the numerical control in the operation of the boiler biweekly daily inspection, to eliminate hidden dangers, operation have to be aware of items, overhaul safety device, check the running status of combustion machine check the interlock control system is normal.
<友情连结> 新利18luck jxf吉祥坊 云顶斗地主